Equipped With:

* Select the Optimal Speed: Ram speed control via an infinitely variable valve allows instant adjustment of air flow to the dual cylinders. A minimum setting creates a creep mode for setup, or select any other position to safely match ram speed with your job.

* Positive Ram Stop: Adjustable stroke depth control is provided by the screw stop for precise repeatability. Raise the adjustable bed and shorten the ram stroke to maximize productivity while reducing air consumption and minimizing the pinch point for safer operation.

* Accommodate a Wide Variety of Tooling: Adjustable die space handles numerous tool sets and reduces or eliminates the pinch point. Per OSHA guidelines, a die space of 1/4″ or less is not a pinch point and provides the safest operation method. Loosen the bed and raise or lower it with the large bed elevating screws. Leveling of bed to ram is easily accomplished using this feature.

* Give the Operator Full Command: Safety hooded foot pedal controls all ram motion. Fully depress control pedal for down stroke. Slightly release pedal to stop advancing the ram. Completely release pedal at any time and the counter-balanced ram automatically retracts to the top of the stroke. For added safety, the ram retracts if air supply is removed.

* Condition the Air Supply: Modular FRL unit is standard on all models to condition air supply to pneumatic components for long life. The unit consists of an adjustable filter/regulator module with pressure gauge. Adjustable flow lubricator module and a three-way lockable shut-off valve. The valve is vented to relieve downstream pressure in the off position per OSHA guidelines. Keyed padlock and lockout tag are included.

* Select the Right Tonnage for the Job: Variable tonnage control provided through the modular filter/regulator/lubricator unit. Lower the pressure to suit the job, reduce air consumption and preserve tooling.

* Run without Interruption: Our fully pneumatic press brakes require minimal service. Designed for simplicity, there are few moving parts to wear out – no motor, clutch or brake to maintain or replace.

* Details that Count: Every Atek-Bantam is designed and built with quality and attention to details. Ram guides are simple to adjust and provide years of service. All critical pivot points are heat treated and equipped with grease fittings. Special bushing material is engineered for high loads to support the rocking lever pivot shaft.

Notes:
Specifications Subject to Verification
Optional Features:
Floor Stand, Part No. BST200 ------------- $640.00
Optional Gauging:
Standard Gauge:
SBG - Basic Rear Mounted and Adjusted Manual Back Gauge (must specify model number of press) -------------------- $730.00
Rear Adjusted Pro-Gage:
PG24568 - Pro-Gage Micrometer Back Gauge, 0 – 4” Precision Dial Travel, (2) Units on (1) Common Crossbar --- $1,870.00
Front Mounted Pro-Gage:
PG1224 - (1) Pro-Gage Micrometer Front Gauge with (4) Axis Mounting System, (bed T-rail not included) ------- $1,230.00
PGTR - Bed Mounted T-Rail, Must Specify Length Needed. Price Shown is Per. Foot and Add $35 Cut Fee ---- $85.00
Front Operated Rear Gauge with DRO:
FABGDRO - Front Adjust Back Gauge w/Handwheel, DRO & Twin Ball Screws, Range: 12T – 18”, 24/42T – 21 “ -- $2,830.00
FABGEXT - Required Extension Kit When Workpiece Support Table is used With Front Adjust Back Gauge -------- $110.00
Smart-Gage CNC Back Gauge:
SG12 - Smart-Gage (1) Axis Programable Back Gauge System for 12 Ton Press Brakes, Quick Clamp Flip Fingers. Stores up to 99 Jobs, 9 Bends per Job, 12 Inch Range, 500 IPM & Retract Delay Feature -- $8,900.00
SG2442 - Smart-Gage (1) Axis Programable Back Gauge System for 24/42 Ton Press Brakes, Quick Clamp Flip Fingers. Stores up to 99 Jobs, 9 Bends per Job, 12 Inch Range, 500 IPM & Retract Delay Feature -- $9,240.00
Optional Stroke Stop:
Front Adjust Stroke Stop:
YDRO Digital Readout Addition to Standard Rear Adjust Y-Axis Ram Stroke Control: $820.00
YFADRO Convenient Front Adjust Y-Axis Ram Stroke Stop with DRO for Repeatable Stop Settings: $1,500.00
Optional Safety Equipment:
Two Hand Control:
SA2 Two Hand Safety Control with Front Workpiece Support Table, 2 Ft.: $2,340.00
NEW→ Physical Barrier Guarding, (L. R. & Rear):
PBG2 Barrier Guards for Left, Right, and Rear of Machine with Access Doors under Lock and Key, 2 Ft.: $3,890.00
NEW→ Safety Mat System, (Front):
SMS28 System for 2 Ft. Machine, includes: 3’ x 8’ Mat, SA2, Operators Control Pedestal & Dual Safety Valve Interface.: $10,380.00
Optional Workpiece Assist Equipment:
Workpiece Support Table:
WT200 Workpiece Support Table for 2 Ft. Machine. (1) Fully Adjustable Table, 2 Ft. Wide x 1 Ft. Deep.: $550.00
Large Sheet Support, (for use with WT):
LSSWT Sheet Support Attachment for WT. (2) Adjustable 2 x 18 Inch Extensions, Clamps to the Underside of Any WT.: $660.00
Large Sheet Support, (for use without WT):
LSS200 Large Sheet Support. (2) Fully Adjustable 3 x 30 Inch Units & 2 Ft. Bed Rail, 0 to 2 Ft. L. to R. Spread, Full.: $760.00
Optional Punch Clamping Equipment:
Segmented Safety Clamp Ram:
CR2 Segmented Safety Clamp Ram for 2 Ft. (4) Individual Clamp Segments, Accepts Safety Tang or Std. Punches.: $1,470.00
Optional Increased Tooling Space:
SH* Additional Tooling Space for Deep Box Forming. * 2, 4, 6 or Any Inch Increase over Standard Tooling Space.: $POR
Atek Press Brake Tooling:
Priced by The Inch, NO Minimum Footage Required.
American Made – 4150 Alloy, All Shapes & Sizes, Specials by Request
• Add $35 Cut Charge to Each Tool
• Add $90 Square End Milling Charge to Each Tool (if desired)
                                                                                                  Nose                       Net                             Wt.                                Price
Part No.           Description                                    Angle          Radius     Vee         Height        Thick        Lbs./Ft.                         Per. Inch
90P100 ------- 90⁰ Punch --------------------------- 90⁰ ------ 1/64’’--------------- 3-3/4’’ ------ 1’’ ------- 13 ------------------------ $ 9
90D375 ------- 90⁰ x 3/8’’ Vee Die ---------------- 90⁰ ------------------ 3/8’’ --- 1-3/4’’ ------ 1’’ ------- 6 ------------------------- $7
90D500 ------- 90⁰ x 1/2’’ Vee Die ---------------- 90⁰ ------------------ 1/2’’ --- 1-3/4’’ ------ 1’’-------- 6 ------------------------- $7
90D625 ------- 90⁰ x 5/8’’ Vee Die ---------------- 90⁰ ------------------ 5/8’’ --- 1-3/4’’ ------ 1’’-------- 9 ------------------------- $7
90D750 ------- 90⁰ x 3/4’’Vee Die ----------------- 90⁰ ------------------ 3/4’’ --- 1-3/4’’ --- 1-1/2’’ ---- 9 ------------------------- $8
90D100 ------- 90⁰ x 1’’ Vee Die ------------------- 90⁰ ------------------- 1’’ ---- 1-3/4’' --- 1-1/2’’ ---- 8 ------------------------- $8
85P150 ------- 85⁰ Punch --------------------------- 85⁰ ------ 1/8’’ --------------- 3-3/4’’ --- 1-1/2’’ ---- 17 ------------------------ $17
85D150 ------- 85⁰ x 1-1/2’’ Vee Die -------------- 85⁰ ----------------- 1-1/2’’ -- 2-1/4’’ ------ 2’’ ------- 18 ------------------------ $18
85D200 ------- 85⁰ x 2’’ Vee Die ------------------- 85⁰ -------------------- 2’’ ---- 2-1/4’’ --- 2-1/2’’ ---- 20 ------------------------ $26
90GP375 ----- 90⁰ x 18 ga. Gooseneck Punch - 90⁰ ------ 1/64’’--------------- 3-3/4’’ --- 1-1/2’’ ---- 11 ------------------------ $14
90GP625 ----- 90⁰ x 14 ga. Gooseneck Punch - 90⁰ ------ 1/32’’--------------- 3-3/4’’ --- 1-1/2’’ ---- 11 ------------------------ $14
30P100 ------- 28⁰ Accute Punch ------------------ 30⁰ ------ 1/32’’--------------- 3-3/4’’ ------ 1’’ ------- 11 ------------------------ $14
30D375 ------- 30⁰ x 3/8’’ Vee Die ----------------- 30⁰ ------------------ 3/8’’ --- 1-3/4’’ ------ 1’’ ------- 6 ------------------------- $12
30D500 ------- 30⁰ x 1/2’’ Vee Die ----------------- 30⁰ ------------------ 1/2’’ --- 1-3/4’’ ------ 1’’ ------- 6 ------------------------- $12
30P125 ------- 28⁰ Accute Punch ------------------ 28⁰ ----- 3/64’’--------------- 3-3/4’’ --- 1-1/4’’ ---- 11 ------------------------ $15
30D625 ------- 30⁰ x 5/8’’ Vee Accute Die ------ 30⁰ ------------------ 5/8’’ --- 2-1/8’’ --- 1-1/2’’ ---- 9 ------------------------- $10
30P150 ------- 30⁰ Accute Punch ----------------- 30⁰ ----- 1/16’’--------------- 3-3/4’’ --- 1-1/2’’ ---- 12 ------------------------ $13
30D100 ------- 34⁰ x 1’’ Vee Accute Die --------- 34⁰ -------------------- 1’’ ---- 2-3/4’’ ------ 2’’ ------- 14 ------------------------ $14
FP137 --------- Flattening Punch ------------------- 0⁰ ------------------------------ 2-5/8’’ --- 1-3/8’’ ---- 14 ------------------------ $16
FD137 --------- Flattening Die ------------------- 0⁰ ------------------------------ 2-5/8’’ --- 1-3/8’’ ---- 14 ------------------------ $16
Delivery:
Subject to Stock